BEGINNER'S PLUMBING: WHAT YOU NEED FOR INSTALLING A BATHTUB

Beginner's Plumbing: What You Need for Installing a Bathtub

Beginner's Plumbing: What You Need for Installing a Bathtub

Blog Article

Call

What're your thoughts about Tools You Need to Install a New Bathtub ?


How to Install a Bathtub: Install an Acrylic Tub and Tub Surround
Mounting a bath tub isn't exactly rocket science, yet it does call for strong plumbing, carpentry, and also sometimes, tiling skills. Replacing an old tub with a new one is additionally a reasonably difficult project. If the old bathtub is readily easily accessible, the project can move immediately; if you need to open a wall surface to get rid of the old tub and position the brand-new bathtub, the job is much harder. In either situation, the project is within a residence handyman's abilities, although you will certainly require an assistant to vacate the old tub as well as set in the new one. Make certain you have actually certified yourself for the task and fit attempting it. Rather than employing a contractor to take control of a halfway-completed project, it is better to think about using one before you begin. Opportunities are you may require a professional plumber to make tube connections.
This post will aid you install a new tub in your bathroom if you have already purchased a new tub and don't require to transform the setup of your previous water supply pipes.
Your devices and also product checklist need to consist of the following:
  • New Tub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Knife

  • Measuring tape

  • Pipeline Caps


  • Getting ready for the Installation


    To start with, the sustaining frame supplied with the bath should be fitted (if required) according to the manufacturer's instructions. Next off, fit the taps or mixer to the bath tub. When suitable the tap block, it is necessary to make sure that if the faucet features a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bath, it is also reasonable to fit a supporting plate under the faucets system to stop stress on the bathtub.
    Fit the flexible tap ports to the bottom of both taps making use of 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. See to it you utilize every one of the supplied washing machines.
    Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom must now be ready to be fitted in its last setting.

    Removing Old Taps


    If you require to change old faucets with brand-new ones as a part of your installment, then the first thing you should do is separate the water system. After doing so, activate the faucets to drain any type of water remaining in the system. The process of removing the existing faucets can be rather problematic because of the restricted access that is often the case.
    Utilize a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the faucets. Have a fabric all set for the remaining water that will come from the pipelines. When the supply pipes have actually been gotten rid of, utilize the same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary faucets from turning during this procedure. When the taps have actually been eliminated, the holes in the bath/basin will have to be cleansed of any old securing compound.
    Before going on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the new taps. If the old taps are longer than the new faucets, then a shank adapter is needed for the brand-new faucets to fit.

    Setting up the Bath tub


    Using the two wood boards under its feet, position the tub in the required placement. The wooden boards are helpful in uniformly spreading the weight of the bathtub over the location of the boards rather than concentrating all the weight onto 4 tiny factors.
    The following goal is to make certain that the bathtub is leveled all round. This can be attained by inspecting the spirit level and also readjusting the feet on the tub till the spirit level reviews level.
    To mount faucets, fit the bottom of the outermost versatile faucet port to the proper supply pipeline by making a compression sign up with; then do the exact same for the other faucet.
    Activate the water as well as examine all joints as well as new pipework for leakages and also tighten them if necessary. Fill the tub and additionally inspect the overflow outlet as well as the normal electrical outlet for leaks.
    Finally, fix the bathroom paneling as described in the supplier's user's manual. Tiling and also sealing around the bath tub needs to wait until the bathtub has been utilized at the very least when as this will certainly settle it into its final placement.

    Fitting New Taps


    If the tails of the new taps are plastic, after that you will certainly need a plastic adapter to avoid damage to the string. One end of the adapter fits on the plastic tail of the faucet as well as the other end offers a link to the current supply pipes.
    If you need to fit a monobloc, then you will certainly need minimizing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
    Next off, position the tap in the installing hole in the bath/basin making certain that the washers remain in area in between the faucet as well as the sink. Safeguard the faucet in position with the supplier provided backnut. When the faucet is securely in place, the supply pipes can be linked to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with regular tap connectors. The previous kind should be linked to the tap ends first, tightening up only by hand. The supply pipes can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been linked.

    Tiling Around the Tub


    In the location where the bath meets the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to crack an inflexible seal, triggering the water to permeate the wall surface between the bath and also the tiling, bring about difficulties with moisture as well as possible leakages to the ceiling listed below.
    You can select from a selection of coloured sealants to assimilate your components and also fittings. They are marketed in tubes as well as cartridges, as well as are capable of securing gaps up to a width of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always load the tub with water before securing, to enable the movement experienced when the bathtub is in usage. The sealant can split rather very early if you do not take into account this movement before sealing.
    Conversely, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise quickly offered on the marketplace. It is advisable to fit the floor tiles using waterproof or water-proof glue and also grout.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    Tools You Need to Install a New Bathtub

    We had been shown that report about Tools You Need to Install a New Bathtub through a friend on another web page. Are you aware of anybody else who is enthusiastic about the niche? Why not promote it. We recognize the value of reading our article about Tools You Need to Install a New Bathtub .


    Ensure plumbing safety.

    Report this page